Satin stitch—Bring the needle up to the right side of the cloth on
one side of the outline. Insert the needle on the opposite side of the outline.
Bring the needle under the fabric to return to the starting edge. Repeat the sequence
to create a smooth row of even, side-by-side stitches. This stitch fills in a
design with rows of straight or slanted stitches across a small, outlined area.
It's a very easy stitch to learn.
Seed Stitch is a filling stitch made up of short stitches scattered
randomly but evenly.
Eye stitch—which is also known as eyelet stitch is made using the
same construction principle as Algerian stitch.

This stitch is simple to work as can be seen in the diagram you simply work
a straight stitch into central hole.

The trick is to create neat central hole. In order to do this be sure that when
you insert the needle into the fabric that the needle is taken down in the center
and reappears through the fabric on the outside of the square. If you want to
make the holes larger with each stitch pull the thread slightly so that the
fabric distorts slightly as it this tensioning action that creates the holes
in the center of each stitch. If you want larger holes again, work on linen
or a fabric that is used for pulled and drawn thread work and use a stiletto
or a fine knitting needle to further define the hole.
Shadow stitch—On the right side, this stitch resembles two rows
of backstitch and on the wrong side the catch stitch. Slant the needle the same
as if making a catch stitch, make a single back stitch, first on the lower side
and then diagonally across on the upper side. Work this stitch on transparent
material so the crossing of threads show through to right side. This stitch
is often called herringbone stitch when crosses are worked on right side.
Chain Stitch—Bring thread to right side of material, hold thread
toward you with left thumb, take a stitch into same hole where thread was brought
up, forming a small loop. Do not pull thread tightly. Bring needle out a short
distance forward and over the loop. Make a second loop overlapping the first
one. Continue along marked line.
Bullion stitch—Bring your needle up (in point 1 let's say) pulling
the thread until taught. Hold the thread in your left hand, thumb and index
towards where the thread came up. (reverse if you are left handed)

Now poke the needle back into the fabric about 1cm away (or however long you
want the bullion to be) - point 2. Don't pull the thread all of the way through
yet.

Bring the needle up again part way at point 1. With needle half in half out
of the hole, wrap the thread around the needle several times. (enough times
to equal the distance between the two points.)

Poke the needle back into point 2, with your left hand hold the needle and coils
against the fabric, while carefully sliding the needle out of point 1 and into
point 2. Once the needle is all the way through keep holding the coils against
the fabric until you have pulled the excess thread all the way through.

This is a stitch which really requires quite a bit of practise so work on a
scrap fabric for a while first.
Stem Stitch or Outline— This stitch is worked from left to right.
Bring needle up through fabric to right side on the line to be outlined. Holding
the thread toward you as shown (or the thread may be swung to the left away
from you), take a short slanting back stitch along stamped line. Make the next
and each successive stitch from right to left and bring the needle out to the
left at the end of previous stitch. Repeat along Line, keeping stitches small
and uniform.
Straight stitch—are made of single isolated stitches. This stitch
can be worked in a regular or irregular manner, in a uniform or varying size.
Single satin stitch is simple to work, with the only concern being that the
stitches should not be too long or too loose. Contrasting threads adds interest
particularly when worked in a free manner at different angles. Straight stitch
is often used to illustrate grass and other landscape details.
Lazy Daisy Stitch—Bring needle up at inner point of petal, hold
thread toward you. Thrust needle down at inner point of petal, 1 or 2 threads
to right of point where thread emerges; bring point of needle out at outer end
of petal, going over thread. Draw loop up to cover petal, thrust needle down
outside of loop to fasten it in place. Bring needle out at inner point of next
petal to left or right.
French knot—Bring the thread out at the required position, hold
the thread down where it emerges with the left thumb and encircle the thread
twice with the needle (see 1). Still holding the thread firmly with your thumb,
twist the needle back to the starting point and insert it close to where the
thread first emerged (not in the exact place or it will simply pull back through).
Pull the needle through to the back, leaving a small knot on the surface, as
shown, or pass on to the position of the next stitch as at 2.

Arts and Crafts Products on our marketplace

Youre number 1 Embroidery Designs resource !!